Web Analytics

I need to get some external bike carrying thingy for my car. A rear rack won’t fit because of the spoiler, unless I fit a tow bar. I don’t have roof rails or those clever recessed fittings. Can I get a couple of roof bars and bike carriers that will clamp on and off in a few minutes with minimal hassle? Or is fitting a roof rack whenever we go away going to be a pain?
Two areas of caution: These boats on their sides create a high profile and resistance. If your speed is 70 and you have a head wind of 20-30 (as we did) that's the same as 90-100...a bit much; I'd keep air resistance to 75 or so combined maximum. If the wind is to the side you'll feel strong buffeting at times, slow it down. Without wind we felt comfortable at 70. Kayaks were strapped according to instructions around J and under factory cross bars. Also had bow and stern tie downs to prevent sliding forward or aft.
I managed to install one UpRide and 3 of the older style Thule bike racks simultaneously on one car (ie 4 bike racks). A total of 3 is relatively easy but adding the fourth bike required the pedals to be removed from the bikes and was quite a squeeze. If you are going to install 3 or 4 bike racks then you will need to alternate the direction in which they face (forward-back-forward-back) and you will need to ensure that the various closing mechanisms on each of the bike racks are relatively easily accessible. Good luck 😉 !

However I am going to comment on some of the installation steps and things to watch out for as it is a little daunting to open the FreeRide 532 and find the bags of various components. Once you’ve installed the FreeRide all of the steps you took will be ‘obvious…in hindsight‘. In the future, fitting and unmounting the BIKE RACK will then only take about 5 minutes per bike rack.
This is a well-made bike rack that improves on the lower FreeRide model in how the bike loads onto the rack and how the bike is restricted from wobbling. Loading on the bike to the frame is relatively easy. It’s quite a bit more expensive than the FreeRide model but offers protection for special carbon frames as well as a wider range of accessories over and above what are discussed in this review.

Finally, a price tag of around 150 bucks is the pretty good value given the high-quality materials and design – though you will be able to find cheaper rear-mounted racks elsewhere if your budget is very tight. Also, don’t forget that this model only has the space to load up two bikes – again, there are options out there with a little more space if you need it.


To simplify your ordering process, The Rack Warehouse lists the most popular selling Thule 450 Crossroad Foot Complete Car Roof Rack fits alphabetically by Auto Manufacturer. You'll find perfect fitting roof racks for most of today's top selling vehicles on this list. Thule 450 Crossroad Foot Complete Car Roof Racks are designed for vehicles with raised railings. If you don't see your vehicle on this list, simply click on the Thule Fit Guide at the top of the page, enter your vehicle information and the Thule Fit Guide will do the rest.
Wobble – At speed your front wheel will wobble. I doubt you will stop all of the wobbling. However you want the frame NOT to wobble much at all. In my opinion this design is better at wobble control than the cheaper FreeRide (then again, I’ve used the FreeRide for over 10 years on motorways, admittedly with occasionally worried glances up through the car’s sunroof)
My latest car is an estate/touring with a set of roof rails so requires a roofbar that can clamp directly to the rail. After looking at the OEM version I decided to take a closer look at the Thule Wing bars. Mainly because the OEM version sat quite high off the roof and from BMW would have cost a small ransom. I have had a few different sets of Thule bars in the past and still own/use a set of Thule ProRide 591 bike carriers so it made sense to have a look at the newer offerings. In addition Thule have a pretty good reputation world wide and certainly have great customer service here in the UK.
Shortly after we bought the rack, our little mazda 2 was rear ended by a texting idiot. Before the car was repaired, I decided to try and test the rack to see if I could damage the tailgate with the rack. I tightened it up really hard and grabbed the mounting arms and shook the car around on it's suspension and it did not bend or damage the tailgates panel edges at all.
For sale is a Thule roof rack. It has 4 x 754 rapid system foot for cars with normal roof ( without bars ) and 2 x 120 cm square load bars. It is lockable and comes with 2 keys and original packaging. The bars have scruffs and scratches from use but are in good working order. I hade this on my 2007 Saab 95. Please make sure this model fits you’re vehicle. I can deliver to most U.K mainland post codes for £10. Thanks for viewing.
Just about every roof rack company offers a standard bike mount for their racks, but not many offer a storage combo setup like the folks at Küat. The Skinny is designed to allow for a combination of a single bike mount and space for up to 160 pounds of gear, leaving the second half of the roof open for anything else you might want to pack on your adventure.
I managed to install two ProRides, the UpRide and a FreeRide simultaneously on one car (ie 4 bike racks). A total of 3 is relatively easy but adding the fourth bike rack required the pedals to be removed from the bikes and was quite a squeeze. If you are going to install 3 or 4 bike racks then you will need to alternate the direction in which they face (forward-back-forward-back) and you will need to ensure that the various closing mechanisms on each of the bike racks are relatively easily accessible. Good luck 😉 !
Seeing a full-on roof rack bolted to the top of an overlander or SUV shouldn’t be a surprise to anyone. For more modest sedans, however, they look a tad out of place. Which is why the Yakima Round Bars make a great alternative. You won’t be carrying fully stocked coolers, kayaks and mountain bikes all at once with your four-door anyway, so there’s no need to go overboard. “We have been using Yakima Load Bars and Storage Boxes for years, both for ski and bike trips, and now even for rooftop storage on our Four Wheel Campers. The Yakima system is proven, classic and adaptable for smaller cars.”
As a wheel-mount bike rack, there is no frame contact made which means it’s one of the best options for transporting bikes with carbon fiber frames. It’s also well-suited for bikes with odd-shaped frame designs or tubing such as downhill mountain bikes with rear suspension systems integrated into the frame or bikes with lots of frame-mounted accessories.
Yakima's new premium rooftop cargo box has clean lines and modern style that today's travelers demand. It's also plenty capable of getting dirty, though, so it's the perfect way to add storage for off-road camping trips. Yakima simplified the installation of this unit, so you'll spend less time in setup and more time exploring the wilderness. The smaller option (15 cubic feet) is great for quick trips, while the larger one (20 cubic feet) is ideal for families or longer jaunts.

The one addition I’d like to see made to this is a clip to hold the wheel straps out of the way when putting the bike in place. You can tuck them behind the wheel mount, but I found they would often flip back over and get in between the tyre and the mount meaning you had to put the bike down, tuck the strap out of the way again before picking the bike up to put in place. Not a big deal, just mildly annoying.
Also have two of the cheaper thule bike racks (maybe they dont even make them any more) ,and again these are mostly fine, the only complaint I have about these is that they are the clamp on type, and the T bolt siezes in the clamp, which most of the time is not a problem, as you should never need to adjust the clamp size. However If I want to use my rack on a friends roof bars (not thule), the clamp size needs altering, but is difficult to do as the T bolt has siezed in the clamp.
I bought these Aero bars for my 2016 Jeep Wrangler Unlimited. Also purchased the Thule 300R gutter low feet. Make sure you link out to the Thule site to determine the right combinations of feet/bars to fit your vehicle when placing your order. The bars are good quality but installation instructions are a joke. They reference the foot pack for installation instructions. The foot pack tells you nothing beyond a vague illustration on how to install. Here is what I found out after several attempts and gouging out flesh on my left thumb:

As a final consideration, even though the UpRide will hold practically any bike you can hoist into its ratcheting hook arm, it really shines when securing bikes with wider tires inflated to lower pressures—i.e. mountain bikes, hybrids, cruisers, and fat bikes. Simply put, the hook can grip the bigger, softer tires easier than with the skinny, high-pressure tires found on road bikes.
Last year I bought a Suburban (now I have two racked vehicles) and bought a set of Thule #450 Crossroads to mount to the factory rails. I was little concerned about the rack coming loose. Not that the rack would have a problem, but rather the factory rails would rip out of the Suburban’s roof. Happy to say, after several 1500 mile trips to Maine and Hilton Head my concerns have been but aside. This thing is as rock solid as I was used to.

Caveat: I was thinking of replacing the Js with a rail rider or something that I could put an extended crossbar on in order to lay the boats flat. Figured less wind resistance would equal better gas mileage. I was surprised to find on this trip my mileage was better than expected (19+ with a big hemi V8, not great but hey, it goes!)I attribute this to mainly reduced speeds on many of the non interstate highways where we were running 60-65.
PayPal Credit is subject to status. Terms and Conditions apply. Performance Cycling Limited acts as a broker and offers credit from PayPal Credit. PayPal Credit is trading name of PayPal (Europe) S.à r.l. et Cie, S.C.A. Société en Commandite par Actions Registered Office: 22-24 Boulevard Royal L-2449, Luxembourg. †Full Representative Example: Representative 17.9% APR (variable), Purchase interest rate 17.9% p.a. (variable), Assumed credit limit £1,200.00.
The rack was easier to install than I had thought, though I suspect your average Swede is much stronger than your average American... They show a one hand squeeze on the Aero Foot cam (that scrunches down on the cross bar, securing it). I had to stand and jump up and down on it (please don't void my warranty!) to get the darn thing to close and snap locked. It was almost a show stopper as I would not have been able to get it to close otherwise (I tried squeezing it for dear life with both hand and all my 205 lbs for over 15 minutes before I gave up and stood on the darn thing: closed right up and locked). Other than that, it went in likity-split, and exactly like the fit kit said it would! It took about 45 minutes, counting the isometirc exercises with the cam. I purchased the lock cylinders: I wanted to make those hard to install, but it could not have been easier. The installation instructions are well written and specific for my car (from the fit kit). I do think there should be no charge for the fit kits...
However I am going to comment on some of the installation steps and things to watch out for as it is a little daunting to open the UpRide 599 and find the bags of various components. Once you’ve installed the UpRide all of the steps you took will be ‘obvious…in hindsight‘. In the future, mounting and unmounting the BIKE RACK will then only take about 5 minutes per bike rack.
Preloved and the heart device is a registered trademark of Moo Limited. Preloved, The Joy of Second Hand, Preloved People and The Second Hander are trademarks of Moo Limited. Copyright 1997 – 2018 Moo Limited. All Rights Reserved. Use of this web site constitutes acceptance of the Preloved Terms and Conditions, Privacy Policy and Cookies Policy. You can manage cookies here.
Based on its versatility, strength and durability, it’s hard to beat the Pioneer Platform range. “We’re running Pioneer Platforms on our Defender 110 and third-gen Tacoma builds, and we have found their system to be durable, affordable, easy to assemble and highly adaptable to a range of uses,” Henwood tells us. “We’ve loaded them with fat bikes, road bikes, camping cargo and with the Rhino Rack Batwing Awning set-up. They do what we ask of them with minimal added weight.”

Looking at some recent reviews, you might come to the conclusion that Thule heard all the complaints here about the end caps being shown in the picture, but not actually being in the box and rectified this problem. Some people claim to have gotten end caps. However, like me, you would be wrong in this conclusion. As of June 2015, they still don't include end caps. Maybe these people saying they got end caps got them with a foot purchase? At least in my case when I was just buying the bars to replace the rusty ones on my car, no end caps.

The ProRide CAN be modified (without any additional new parts) so that the controls can be used on either the left-side or right-side of your car. It’s explained in the manual and take about 15 minutes to do for the first time. As a flavour of what you need to do here you can see that the end of the ProRide comes off and the mounts can then be slid off and turned around to face the other direction.


You see we've already got our front rail installed. Just use a reference mark here to make sure we have that in line. You're going to do the same thing here in the backside.Once we have that position from both sides, we want to check the overhang that we have on our bars. We'll just add as well. The overhang's going to be this portion here. I just want to make sure we have equal overhang on both sides. It doesn't have to be perfect, but it certainly looks better if it is. All right. Once we've got that where we want it, you want to grab the tool that is provided. This is a torque limiting tool, so basically it's going to tell us when we have our bars tightened down all the way. This is a four nanometer tool. Right here it says Ford inaudible 00:02:09 Newton meter, this is a Ford Newton meter clamp. So, we'll just start tightening this up. I like to snug this one down pretty well. Make sure that this portion here comes over and makes contact with my race side rail there. Once I get that pretty snug, I'm going to go over and do that other side.Now, these roof rack systems are going to be an excellent way to free up some space inside your vehicle of course. Bike racks, cargo carriers, rooftop cargo boxes, kayak carriers, just all kinds of different accessories that you can put up here on the roof line. Ski and snowboard carriers or really the enclosed ones, even if you want to transport some luggage and stuff like that, keep them out of the elements. Now I'm gonna go ahead and torque this one down until my tool indicates, you see that's just like a gas cap basically. Once it's tight enough, it's just going to click. Same thing here.Now with the Evo Bar, something I do like, you see this cap is going to come right open. That allows us to get into our T-slot accessory and no longer do we have to remove the long rubber strip and cut it. Our accessory can slide right in that gap and almost self seals right around it. Makes it really easy to use. Just pop that back down like that. To finish up our install though, we do want to cap off our end caps here. Tab here is going to go on the top, push that bottom in and at that point, you'll just rotate this 180 degrees into it's locked position to lock that cap on. These are just plastic cores. You can do these using a screwdriver, so if you wanted additional security, you want it to be able to lock and we do have the Thule locking keys you can put in there and then actually have a key lock to keep that nice and protected.The bars do come in a black or a silver, so if you wanted something to blend in with the Cherokee, I'd go with the silver. You want something to stand out, I'd go with the black and then I'll show you on that front bar here on the bottom side, once we get everything in position, we've got a little tab right here. We pull that tab over to our foot pack. That's going to eliminate any gaps in the bottom of that crossbar. Really going to help to eliminate wind noise. You can see right here, just gonna pull that over. It's going to close up that gap. Same thing on our front bar. Th
I recently put my Thule J-racks on for their second season of use, only to fine that the mounting hardware is not for its second summer of use. The mounting bars (plastic) are cheap and split easily. There is a bolt inside the mounting bar that is supposed to stay stationary so that the bolt may tighten the rack to the rack. When plastic mounting bar splits, which doesn't take much, the bolt moves around making the hardware useless. Also, the bolts included with the racks rust at the mere mention of water. (Probably not the best thing for a kayak rack). The upside is that the J-rack itself is great, its just the mounting hardware that stinks- which can be replaced. I've yet to do it so I can't speak to how easy that is. Its not a bad rack for $85, just be prepared to replace and be careful witht the mounting hardware aspect of it.

Choose aerodynamic roof bars for superior performance and a sleek, sophisticated look that complements the lines of your car. These roof rack cross bars also have many smart design features. A textured surface disturbs the airflow and greatly reduces wind noise. The aluminium extrusion creates one of the strongest load bars in the market. The design gives you quick, no-hassle installation. While the end cap pivots and T-track make it easy to add further loading options.
×