Web Analytics

The hull a port I like it because it fits almost every rack. And like most of the reviews wonder why it has plastic mountings. Well, figured that out one day when driving under a garage where the door was a little low. The clamps under the hull a port broke. But then don't think they were designed to drive into a roof. Have tightened those hex bolts pretty tight, so the plastic bends but doesn't break under designed usage. But the hullaports do shimmy and shake when there isn't a boat attached. The angle of the j-shape fits one of my boats perfectly (Chilco) but on my Quest it isn't deep enough, I would like a better fit.
I used the rack with a standard road bike and a mountain bike with a big chunky downtube, both were clamped snuggly in place as the rubber lining of the clamp moulds around the tube whatever its shape. We got the quick release wheel straps over a set of Cannondale Knot 64mm deep section wheels and there was plenty of strap to spare. The design of the mounts also means any width of tyre will fit with the possible exception of fat bikes.
You see we've already got our front rail installed. Just use a reference mark here to make sure we have that in line. You're going to do the same thing here in the backside.Once we have that position from both sides, we want to check the overhang that we have on our bars. We'll just add as well. The overhang's going to be this portion here. I just want to make sure we have equal overhang on both sides. It doesn't have to be perfect, but it certainly looks better if it is. All right. Once we've got that where we want it, you want to grab the tool that is provided. This is a torque limiting tool, so basically it's going to tell us when we have our bars tightened down all the way. This is a four nanometer tool. Right here it says Ford inaudible 00:02:09 Newton meter, this is a Ford Newton meter clamp. So, we'll just start tightening this up. I like to snug this one down pretty well. Make sure that this portion here comes over and makes contact with my race side rail there. Once I get that pretty snug, I'm going to go over and do that other side.Now, these roof rack systems are going to be an excellent way to free up some space inside your vehicle of course. Bike racks, cargo carriers, rooftop cargo boxes, kayak carriers, just all kinds of different accessories that you can put up here on the roof line. Ski and snowboard carriers or really the enclosed ones, even if you want to transport some luggage and stuff like that, keep them out of the elements. Now I'm gonna go ahead and torque this one down until my tool indicates, you see that's just like a gas cap basically. Once it's tight enough, it's just going to click. Same thing here.Now with the Evo Bar, something I do like, you see this cap is going to come right open. That allows us to get into our T-slot accessory and no longer do we have to remove the long rubber strip and cut it. Our accessory can slide right in that gap and almost self seals right around it. Makes it really easy to use. Just pop that back down like that. To finish up our install though, we do want to cap off our end caps here. Tab here is going to go on the top, push that bottom in and at that point, you'll just rotate this 180 degrees into it's locked position to lock that cap on. These are just plastic cores. You can do these using a screwdriver, so if you wanted additional security, you want it to be able to lock and we do have the Thule locking keys you can put in there and then actually have a key lock to keep that nice and protected.The bars do come in a black or a silver, so if you wanted something to blend in with the Cherokee, I'd go with the silver. You want something to stand out, I'd go with the black and then I'll show you on that front bar here on the bottom side, once we get everything in position, we've got a little tab right here. We pull that tab over to our foot pack. That's going to eliminate any gaps in the bottom of that crossbar. Really going to help to eliminate wind noise. You can see right here, just gonna pull that over. It's going to close up that gap. Same thing on our front bar. Th
I replaced my 89 Plymouth Voyager with a 98 Voyager and the roof rack stinks for my canoe and kayak. I replace it with the Thule rack. This rack is strong and sturdy worth every penny. The factory installed racks could slide back and forth and the Thule can't slide with loosening the bolts. I have no intention of ever moving them so I have no problem with this.
Look out for our 'One Key System' lock matching offer. When you put Thule products in the Shopping Basket we automatically calculate how many identical replacement lock barrels you'll need so you can lock all your Thule gear with the same key. We'll charge you a nominal price for each of these replacement lock barrels, refunding you the same price for each lock barrel posted back to us.
×